“ether mining rig build best”

“ether mining rig build best”

Ethpool and Ethermine operate with two separate websites, but contribute to the same mining pool; it is probably a merger. This pool accounts for about 25% of all the hash rate power on the Ethereum network. It can be regarded as the biggest mining pool for this cryptocurrency, and they charge an amazingly low fee of only 1% of the miners’ reward.
The GTX 1060 has a hashrate of between 22-27 MH/s (Ethereum) depending on overclocking, and which memory brand is installed on your card.  The card consumes between 90 and 100 watts of electricity. It can currently be purchased for roughly $250 on Amazon and Newegg. This gives you a break-even time of 3.5 months.  Much better than a Titan V!
1. You published this article on January 19,2017 and you talk about RX 480, but you recommend a driver that is not for this type of video card. I know that Claymore recommends it, but I think it was long time ago, when he wrote his program.
I purchased 6 1070 FTW edition GPUs and they have two 8-pin power connectors each. Do I need to get more powers supplies to accommodate the extra 8-pin slot? Also, should I have connector branch from the power supply to both 8-pin slots or give each slot on the GPU its own connector to the power supply?
A Bitcoin ASIC’s specification could be seen as having a certain hash rate (e.g. Gh/s) at a certain efficiency (e.g. J/Gh). While cost is another factor, this is often a relatively fixed factor as the minimum cost of a chip will be determined by the fabrication process, while the maximum cost will be determined by market forces, which are outside of post-fabrication technological control.
I’m mining at poolmining.org a small EU based pool that started about 2-3 months ago. Only found 2 ethereum blocks so far all in a single day (crazy variance), but the payout for me was more than satisfactory – I have 2x 1070. The pool has vardiff, PPLNS and a really dedicated pool operator that you can actually talk to through the support forum.
The other more recent launch in the fork of a dedicated Ethereum mining pools that you might want to check out is DonkeyPool. The pool apparently only supports getwork for the moment it has found a few blocks already, though the number of miners and the hashrate is not that big yet. The pool will run without a mining fee until June 15th, 2016, then the fee will be 0.5%. The payouts are made once a day if a minimum 1 ETH balance is available.
What is the best ethereum pool? The answer is, not one. All are equally as reliable as then next. The only differences they have is fees they charge. It’s also important to be close to server for better connection and speed.
Even though Ethpool and Ethermine are two separate sites, they are part of the same Ethereum mining pool. At the moment, Ethpool and Ethermine sites are the largest Ethereum mining pools. Ethpool and Ethermine allow for 25% of the network hash power.
Basically, you need to get the necessary GPUs, as many as are necessary or affordable and looks for the most efficient ones. They are usually hard to find. Next, get a motherboard and a power unit which can support all your GPUs at once. You may also need a CPU, RAM, a processor and a rigged case. The most important necessity here, however, is the management of the rig, settling the payment agreements for the respective miners, based on their performance, and their charges also, as the case may be.
Great guide, I wish I had this a few months ago before I started mknkn. I’ve gone through all this the hard way which is good but this guide is very clear and straightforward. Having said that I wonder if you would have any idea how to fix the issue I have come across. After mining for two weeks on windows 10 with claymore on nanopool @ 6 x 1070 GeForce. My miner went offline. It says “ cannot write a buffer for DAG” CUDA error 77. It also says “an illegal instruction was encountered” and “calc DAG failed” I have increased the virtual memory but that did not work. My hard drive says it has not 15gb of 110.
Solo mining might have the best payout of the three methods if you have the financial power to invest in several GPUs and pay mammoth electricity bills. To carry out solo mining successfully, you need to hit at least 100 mega hashes per second and this hash rate will increase as difficulty rises. However, you get all the rewards; they include payment for uncles on top of your earnings.
To get something out of eth mining you need to put something in. The main costs you’ll face include the hardware and setup costs as well as the maintenance costs. These costs apply to solo mining and pool mining. For cloud mining, the fee you pay for a contract is your cost.
However, once you have your GPU cards, they will need power. Therefore, the second most important factor is how much your card will consume, and how much you’ll need to pay for this. In order, to calculate this, you’ll need to find out how much power it uses and how much you need to pay per KW/h. These are respectively 150W and $0.10 per KW/h for me. To calculate the per hour cost just convert W to kW (by diving by 1000) and multiply together, so for me the rig would cost 0.15*0.1= $0.015/hour to keep alive. This amounts to $0.36/ day or $10.80/month.
If you have a quality mining rig, low electricity costs, and join a mining pool with low fees, you can earn a couple hundred bucks a month. There are numerous variables that affect this calculation, though.

One Reply to ““ether mining rig build best””

  1. Dwarfpool is an Ethereum mining pool that contributes less than 5% of the hash rate power. Although it has declined in its performance, it is still very reliable. It also charges just a percent of the miner’s reward, but the downside of using Dwarfpool is that the threshold payout is 1.01 ETH, which means more time before rewards are gotten. It is good for those who have very powerful Ethereum mining equipment.
    Joining the Ethereum mining pool is the next step after you have obtained the proper Ethereum mining hardware. The adequate and reliable mining pool will aid you in getting more frequent payouts. This is in comparison to getting paid only when you solve an Ether block.
    With every good there will be some complaints, as customers found that the drivers in the card had a tendency to stop working. Some have also said that when they were playing games with this card installed, the screen would start to flicker and even cause the system to freeze only after 10 minutes of gameplay.
    OuterVision Mining Rig Builder and Profitability Calculator provides computer part selection, compatibility, and pricing guidance for do-it-yourself Ethereum cryptocurrency mining rig builders. What makes us different? Besides the largest and most accurate power consumption database, we provide a comprehensive mining rig parts compatibility guidance, up-to-date pricing, and profit calculations for mining Ethereum cryptocurrency. Combined with precise power supply efficiency data, OuterVision Mining Rig Builder can accurately calculate a true power cost of your Ethereum mining rig and recommend the best bang for the buck power supply for your build. For more comprehensive PC power consumption calculation check our Power Supply Calculator tool.

Leave a Reply

Your email address will not be published. Required fields are marked *